2024年4月11日发(作者：)

Designation: D 3359 – 02

名称： D 3359-02

Standard Test Methods for

Measuring Adhesion by Tape Test

1

用胶带测量附着力的检测标准

This standard is issued under the fixed designation D 3359; the number immediately following the

designation indicates the year of original adoption or, in the case of revision, the year of last revision.

A number in parentheses indicates the year of last reapproval. A superscript epsilon (e) indicates an

editorial change since the last revision or reapproval.

这个标准是

D 3359

确定了以后发行的。数字代表名称最初通过的时间，或者修订情

况，和最新版本。括号内的数字代表最新重新审批时间。上标代表最新版本的变化

或重新审批。

This standard has been approved for use by agencies of the Department of Defense.

该标准已经被国防机构部门批准使用。

1. Scope 范围

1.1 These test methods cover procedures for assessing the adhesion of coating films to

metallic substrates by applying and removing pressure-sensitive tape over cuts made in

the film.

这些试验方法覆盖了对金属涂层片附着力的评估。附着性通过在涂层切口处施加和

去除透明压敏胶带来评估。

1.2 Test Method A is primarily intended for use at job sites while Test Method B is more

suitable for use in the laboratory. Also, Test Method B is not considered suitable for films

thicker than 5 mils (125µm).

试验方法A主要用于工作场所，而试验方法B更适用与实验室。试验方法B不适宜

在涂层厚度大于125微米时使用。

NOTE 1—Subject to agreement between the purchaser and the seller,Test Method B can

be used for thicker films if wider spaced cuts are employed.

在买方和卖方之间的协议，如果允许更宽的切口，方法B可以用在更厚的涂层上。

1.3 These test methods are used to establish whether the

adhesion of a coati

ng to a substrate

is at a generally adequate level. They do not distinguish between higher levels of

adhesion for which more sophisticated methods of measurement are required.

这些试验方法被用来确定涂层对底材是否有足够的附着力。不区分层次,以服从需

要更先进的测量方法。

NOTE 2—It should be recognized that differences in adherability of the coating surface

can affect the results obtained with coatings having the same inherent adhesion.

备注2：应该承认，涂层表面附着力的差异影响涂相同附着性的涂层得到的结果。

1.4 In multicoat systems adhesion failure may occur between coats so that the adhesion

of the coating system to the substrate is not determined.

多层系统的失效发生涂层之间，以致使涂层与基层之间的粘附性无法确定。

1.5 The values stated in SI units are to be regarded as the standard. The values given in

parentheses are for information only.

SID单位价值被视为标准，括号内的价值是仅供参考.

1.6 This standard does not purport to address the safety concerns, if any, associated with

its use. It is the responsibility of the user of this standard to establish appropriate safety

and health practices and determine the applicability of regulatory limitations prior to use.

这个标准不打算讨论安全问题,如果有的话,再加上使用. 用户有责任建立适当的安全

标准和卫生管理办法和确定适用前使用限制.

2. Referenced Documents 参考文件

2.1 ASTM Standards:

美国材料与试验协会标准

D 609 Practice for Preparation of Cold-Rolled Steel Panelsfor Testing Paint, Varnish,

Conversion Coatings, and Related Coating Products

2

D609实际编写冷轧钢板测试油漆、油光漆、转换材料、涂料及相关产品

2

D 823 Practices for Producing Films of Uniform Thickness of Paint, Varnish, and Related

Products on Test Panels

2

D823方法制作影片制服油漆厚度、油光漆及相关产品测试板

2

D 1000 Test Method For Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical

and Electronic Applications

3

D1000测试方法压力敏感粘合剂镀磁带用于电器及电子应用

3

D 1730 Practices for Preparation of Aluminum and Aluminum-Alloy Surfaces for